Iscar Offers A Completely New Family Of Slitting Cutters Utilizing Tang-Grip Technology And The Durability Of Sumo Tec Grades

Iscar now offers a family of high-performance slitting tools that merge the convenience and security of Tang-Grip clamping with the added sturdiness of the new Sumo Tec insert grades. The conception, already validated successful in Tang-Grip parting tools, has now been extended to slitting cutters. In the patented Tang-Grip clamping system, inserts are press-fit into their pockets accompanied by a special hand tool, and are clutched firmly in place without having the need for clamps, upper jaws or set screws that can weaken the insert and hinder chip flow. The pocket composition uses cutting forces to keep the insert seated firmly in position, eliminating any prospect of insert pull-out. The Tang-Grip clamping system also fosters more accurate slitting cuts plus increased pocket and insert life. Iscar's Sumo Tec insert grades feature a distinct post-coating treatment which considerably improves tool life and dependability. Introduced in late 2007, the brand new Sumo Tec treatment flattens the insert's coated surface to eliminate microscopic stress raisers, decrease heat and friction and boost chip flow. The result is improved toughness and resistance to chipping and built-up edge, all leading to greater tool life. The golden-colored side on Sumo Tec inserts facilitates wear detection. Size for size, Tangslit cutters give more teeth than Iscar's SGSF cutters, enabling higher feed rates. Their improved rigidity leads to straighter, better accurate cuts and diminished vibration even in large-diameter cutters. The new Tangslit TGSF cutters come in 100 to 160 mm diameters, 3 and 4 mm widths and can accommodate the exact same selection of inserts as Tang-Grip parting tools. Some other sizes will be added. Available Sumo Tec grades for Tangslit cutters include: IC808, with a tough submicron substrate below a Sumo Tec TiAlN PVD coating, offering superior resistance to impact loads and built-up edge. This grade is suggested for slitting heat resistant alloys, austenitic stainless steel, hard alloys and carbon steel. IC830, providing additional toughness for heavier parting and grooving including interrupted cuts. It is fitting for any stainless steel and high temperature alloys. IC908, a hard, fine-grain substrate with exceptional chipping resistance, mixed with a new Sumo Tec TiAlN PVD coating. It is ideal for nodular or gray cast iron. IC928 and 928A, PVD TiAlN-coated tough grades suitable for stainless steel, high temperature alloys and other alloy steels. These grades are likewise recommended for interrupted cuts and heavy operations. Each Tangslit and Tang-Grip inserts are available in J- or C-type chipformer geometries from Iscar. Iscar Adds Their Latest Creations To A Extended Line Of Successful Hole Generating Solutions Iscar recently released several different drilling innovations to meet their customers needs. These new products are Sumocham Drill, DR-DH and Deep Drills. Drawing off of their experience Iscar has come up with new and innovative ways to increase productivity for the end user. Iscar Recently Releases A Variety Of New Lines To Increase Their Family Of Milling Tools Iscar recently released a new family of High Speed Milling adjustable endmills and facemills that will improve milling of aluminum, non-metallics, cast iron and hardened steel. This should prove especially useful in the automotive and aerospace industries. A Few Of The Many Improvements In Carbide Inserts By Iscar From Over The Last Decade Iscar is introducing a new unique milling system with tangential, clamped, butterfly-shaped LNKX carbide inserts. The butterfly-shaped insert has significant advantages compared to the current flat, square shapes. The new geometry has more cutting edges, positive rake face, reduced cutting forces resulting in higher performance. Many Progressions Have Extended Iscar's Families Of Indexable Endmills For Increased Productivity Helido-Upfeed 04 Two years ago Iscar introduced the extremely efficient H600 indexable endmill line, based on conceptually new Helido-Upfeed double sided inserts with 6 cutting edges. The first insert launched was the H600 WXCU 0806..., which was designed for milling cutters in the diameter range of 50 to 125 mm. The Latest In Carbide Endmill Configuration In A Extensive And Prospering Family From Iscar Manufacturers and die & mold shops can eliminate chatter problems in many milling operations with Iscar's new Chatterfree endmills. The cutters' variable-pitch flute pattern eliminates harmonic vibration, the main source of chatter. This enables faster cutting and finer finish in rough or finish slotting, shoulder milling and cavity milling. Industrial Water Heater - Considering All Of Your Needs - Read Thoroughly In Order To Know A Lot More Looking into a commercial water heater? Then you have a few things that you must consider. Take a look at these areas to avoid making a mistake with the wrong unit. Commercial Water Heater- Which Is Right For Your Requirements If you are in the market for a commercial water heater then consider what the needed application is and your overall cost to determine which is best for you. Since there are so many to choose from you may have to do some calculating in order to match the need.

A Few Of The Many Improvements In Carbide Inserts By Iscar From Over The Last Decade New End Mills Coming From Iscar Will Expand Productivity While Decreasing Costs Many Progressions Have Extended Iscar's Families Of Indexable Endmills For Increased Productivity The Latest In Carbide Endmill Configuration In A Extensive And Prospering Family From Iscar Push Pull Testing For Building Industry With Calibrated Measuring Instruments. Mechanical Load Testing Procedures For On Site Proof To Testing Demands. Iscar Offers A Revolutionary Family Of Slitting Cutters Using Tang-Grip Technology And The Sturdiness Of Sumo Tec Grades A Couple Of The Many Advancements In Carbide Inserts By Iscar A Few Of Improvements In Carbide Inserts By Iscar Over The Last Decade A Number Of Developments Have Increased Iscar's Line Of Indexable Endmills For Heightened Productivity A Variety Of Advancements Have Increased Iscar's Families Of Indexable Endmills For Elevated Productivity The Latest In Carbide Endmill Configuration In A Extensive And Prospering Line From Iscar The Newest In Carbide Endmill Configuration In A Extended And Successful Line From Iscar

Bulk Water Biz Podcasts

Home | About Us | Products | News | Contact Us Copyright © Biz Podcasts 2009 onwards initial design by Templatesbox with thanks, altered almost, but not quite, beyond recognition by us lol